Water Softener Maintenance – Easy Steps
Water Softeners are the most important appliance of your home, as we have to drink water and we need it to be more pure and cleaner. Its Effect our health if we not make sure to maintain it and keep it clean and avoid all the related complications those could be happened in negligence. We will try to explain the more important steps to keep maintenance of water softener in efficient way.
Table of Contents
How Water Softener Works ?
Before Starting about maintenance, i want you to know how it works below is the image explaining about components of water softener as well give you brief idea that how its actually works
Avoid salt bridges and salt mushing – Check the Salt Level every month
A salt bridge occurs when a hard crust forms in the brine tank and creates an empty space between the water and the salt, preventing the salt from dissolving into the water to make brine. Without the brine, the resin beads that soften your water can’t do their job. Common causes of bridging include high humidity, temperature changes around the water softener or using the wrong kind of salt. You may have a salt bridge if your salt tank appears full but you know your water isn’t soft. The quickest way to test for a salt bridge is to take a broom handle and carefully push on the top of the salt, using a little bit of pressure to break it up if it has solidified.
Salt mushing in water softener
Salt mushing is the more serious of the two problems and happens when dissolved salt recrystallizes and forms a sludge on the bottom of the brine tank. This thick layer of salt keeps the water softener from properly cycling through the regeneration process, leaving your water hard and creating a serious blockage in the tank. If you test for a salt bridge but it doesn’t break up when pushing on it, salt mushing is probably the cause. Draining the softener of its water, digging out all the old salt and replacing it with fresh salt is the only way to fix this problem.
To avoid these salt snafus, opt for high-quality salt pellets, which greatly reduce the potential for any problems—especially salt mushing. Additionally, don’t overfill your brine tank with salt. Keeping it half-full prevents older salt from sticking to the walls of the tank. Finally, it’s important to manage the humidity level around your water softener. If it’s too humid, condensation can occur in the brine tank, causing the salt to bond together and bridge.
Know the Type of the Salt
There are three basic types of water softener salt: rock, solar and evaporated. Rock salt, the least expensive, contains higher levels of insoluble minerals or impurities. Over time, this can result in a muddy tank, decreasing the softening efficiency while leaving impurities in your water. Solar salt, which is much more soluble than rock salt, is obtained by the evaporation of seawater and is found in both pellet and crystal form. The best option is evaporated salt, which is obtained through a combination of mining and evaporation. This is the purest form of salt at 99.99% sodium chloride.
In general, look for higher purity salts, which will leave less storage tank residue, lowering the likelihood of salt bridges and salt mushing, and will result in less maintenance. High-quality salts—and salts in pellet form—help eliminate bridging problems. Additionally, many leading brands also offer salt products that address specific issues, such as high iron concentration, rust stains and sodium alternatives.
Even though your resin beads are routinely recharged by salt, it doesn’t hurt to flush the resin bed every few months with a water softener cleaner to keep it in top form. Over time, a water softener can become polluted with iron, silt, heavy metals and other organic compounds that cause your softener to lose its efficiency. To reduce the incidence of ineffective resin, simply pour the manufacturer’s recommended amount of water softener cleaner down the brine well and regenerate the system manually. The cleaner is then discharged during the normal flushing process of the water softening cycle. This action keeps the resin “clean” and able to absorb as much calcium and magnesium as possible throughout its lifespan.
Clean the venturi valve
The venturi and nozzle create the suction to move brine from the brine tank into the resin tank during the regeneration cycle. Because of this, the venturi valve sometimes gets plugged with sand, sediment and dirt, so a clean valve is imperative for the water softener to work properly. Simply unscrew the valve cover (don’t worry, there are no special tools required) and remove the internal parts, giving them all a good cleaning in soapy water. This process should be done twice a year to keep the water softening process smooth and efficient.
By periodically giving your water softener a checkup, you’ll keep it running smoothly. Take a closer look at what hard water costs you if your home is left untreated.